Hereis a topology in which there is a router and a switch and some end hosts. 2 different VLANs have been created on the switch. The router's interface is divided into 2 sub-interfaces (as there are 2 different VLANs) which will acts as a default gateway to their respective VLANs. Here, we have assigned VLAN 2 to the specific switch KonfigurasiDasar Cisco IOS Router dan Switch. SW1(config)#vlan 10 SW1(configvlan)#interface FastEthernet0/1 SW1(configif)#switchport mode trunk SW1(configif)#interface range FastEthernet0/24 Sw1(configif)#switchport voice vlan 10 4 Test IP Phone Jika konfigurasi Router dan Switch sudah benar IP Phone secara otomatis akan mendapatkan IP address
Thereare three inter-VLAN routing options: Legacy Inter-VLAN routing - This is a legacy solution. It does not scale well. Router-on-a-Stick - This is an acceptable solution for a small to medium-sized network.; Layer 3 switch using switched virtual interfaces (SVIs) - This is the most scalable solution for medium to large organizations. 4.1.2 Legacy Inter-VLAN Routing

RecommendedRouters. WiFi Routers. WiFi 6 Routers. Network Expansion. Range Extenders. Powerline. Access Points. Switches. 5-Port Switches. 8-Port Switches. 16-Port Switches. Configurations on Switch 2: Step 1. Go to L2 Features > VLAN > 802.1Q VLAN > VLAN Config, create VLAN 10, VLAN 20 and VLAN 30; add Untagged port 2,

Crearuna topología con 2 VLAN utilizando solo 1 Router y 1Switch, para que se puedan comunicar entre sí. Práctica 7 VLAN´s 1 Router y 1 Switch(Laboratorio) PRESENTA: 221210010.

Ifyou want to create a VLAN, you can do this by giving the name and id directly: Switch (config)#int fa0/0 Switch (config-if)#switchport mode access Switch (config-if)#switchport access Vlan 2. Now you can also assign the range of switch ports to whatever VLAN you want: Switch (config)#int range fa0/0-2 Switch (config-if)#switchport mode Masukrouter 2, tambahkan ip. #int fa0/1 #ip address 255.255.255.128 #no shutdown #int fa0/0 #ip address 192.168.10. 255.255.255. #no shutdown Masuk ke switch 2, lalu buat vlan. Switch#vlan database Switch (vlan)#vlan 30 name gepenk Switch (vlan)#vlan 40 name penyok Masukkan interface-nya. Switch (config)#int range fa0/1-2 Inthis example, we are excluding the router address. Step 4. ip dhcp pool name. Example: Router (config)# ip dhcp pool dpool1. Router (config-dhcp)#. Creates a DHCP address pool on the router and enters DHCP pool configuration mode. The name argument can be a string or an integer. Step 5.
Ihave a Cisco SG300 managed switch I am attempting to configure to handle two VLANs one for data (VLAN1) and another for voice (VLAN20). Ports 1 and 52 are configured to trunk to the router/firewall, and to a second SG300 switch , respectively.The remaining ports 2-48 on both switches are set to.
wbTbFG7.
  • 5itrtnwiyv.pages.dev/854
  • 5itrtnwiyv.pages.dev/85
  • 5itrtnwiyv.pages.dev/885
  • 5itrtnwiyv.pages.dev/691
  • 5itrtnwiyv.pages.dev/560
  • 5itrtnwiyv.pages.dev/542
  • 5itrtnwiyv.pages.dev/334
  • 5itrtnwiyv.pages.dev/336
  • 5itrtnwiyv.pages.dev/40
  • 5itrtnwiyv.pages.dev/894
  • 5itrtnwiyv.pages.dev/488
  • 5itrtnwiyv.pages.dev/264
  • 5itrtnwiyv.pages.dev/869
  • 5itrtnwiyv.pages.dev/13
  • 5itrtnwiyv.pages.dev/126

    • vlan 2 switch 1 router